Beneteau 40 & 43

Comment

Comment by Michael Boyle 8 hours ago

Hi All,

french built 2010 43 has been very dry down below but now a slow leak has occurred which is showing at the limber holes under the floor board in forward cabin. Bilge pump goes every 3hrs for 20secs. Not sure if it’s fresh/rain water or salt, tastes slightly salty. Water pump doesn’t cycle so not fresh. Checked all sea cocks and bow thruster no obvious leaks. Think it must be deck fitting leaking in heavy rain, which we have had. Not on board as laid up afloat so can’t monitor easily.

Anyone had similar any suggestions

Comment by Michael Boyle on September 24, 2024 at 7:30am

Hi all

I’ve decided that the time has come to replace the main on My 2010 French built 43. Original main is Elstrom sail and has stood up well, don’t know cloth used, still has good shape but put a couple of tears in main during double handed cross channel race and the stitching is starting to go.

replaced genoa 3 year ago.

What I looking for is experience of or advice on having the mainsail fully batoned. Mostly do cruising and some club racing but want to ensure longevity 

any advice or experience please

Michael Barti Blue

Comment by Dave Shore on March 15, 2023 at 9:03am

I need to purchase the sump control box for the forward head on my B43. The pump will not turn on automatically anymore, just when I throw the switch. Any ideas?

Dave

Comment by Robert & Sandy on December 1, 2021 at 4:38am

DOLPHIN BATTERY CHARGER - 40 AMP

Hi all,

The Dolphin charger on my 2010 43 is still charging perfectly well EXCEPT the cooling fan is cycling on and off every 20 seconds.. There is a light on the centre top of the unit flashing red, does not look happy. Sadly I cannot locate the instruction manual which, knowing Beneteau undoubtedly came with the boat.

Any help or clues, it seems as if the thermostat controlling the fan is out of order as the unit itself is not hot, not even warm.

Regards,

Bilgolabands (Liberte)

Comment by Mike Brown on October 11, 2021 at 8:15pm

Robert glad to hear you go the problem solved.

mike

Comment by Robert & Sandy on October 11, 2021 at 6:03am

Thanks for all your comments my friends at Seaknots.

The halyard has been rerun without passing through the small stainless steel eye, as seen easily in the pic provided by Chris on 17th August.

All furling now takes place without any undue effort, only unfortunate thing is we had to pay the rigger to run the halyard correctly.

Regards

Bilgolabands

Comment by Chris on August 17, 2021 at 5:27pm

This arrangement works for us:

IMG_3947%20%28003%29.JPG

Comment by Brian Wanamaker on August 17, 2021 at 10:38am

Over the sheave inside the mast then out through the mast about 6 feet from the mast base.

Comment by Brian Wanamaker on August 17, 2021 at 10:36am

Ste spinnaker halyard should be put back through the mast. Over the sheave inside the mast then out through the base. 

I had a profurl furler. If you have the same there has to be a "Twist Stop" attached to the forestay near the top above the upper bearing.  It stops the furled sail halyard from twisting around the sail at the top.  It is about 4 in diameter, looks like a flying saucer with half of the outer edge cut out. Sounds like the rigger may have left it off.  Also if the jib halyard is to tight hte upper bearing will be "tilted" and may be the problem when furling the sail.  Hope this helps.

Comment by Mike Brown on August 17, 2021 at 8:02am

Robert, we added the halyard after we purchased the boat primarily as a way to reach the mast top. When I asked to have it run directly to the top and not through the eye the service manager refused to do so. Apparently there was a concern that leading directly from the top of the mast would create excess pressure on the rigging. I hope this helps. 
Mike

• ‹ Previous
• 1
• 2
• 3
• …
• 7
• Next ›
• Page