SeaKnots

Hi all. Just installed the main with a friend that did not, in my opinion, keep enough tension on the outhaul when I was rolling the mainsail inside the mast.

While on the water today, I was unable to get the main out. It started OK, but after two feet, it seems like all the sail wanted to come out at once, which blocked the mainsail in the slot. The first batten comes out about its half at an angle (foot first...) and seems to contribute to the problem.

I can get the sail in and out in that 2 feet length.

Anyone has a solution for this?

Thanks in advance!

Views: 285

Replies to This Discussion

At dock try squirting a water hose on the mast slot, attempting to get the sail as wet as possible. Then work the sail back and forth a few inches at a time, trying to tighten the "roll". This has worked for me. It is a tedious and time consuming thing, but I prevailed and it worked.

Sam

LONGHAWK B43, #9

Of course this have never, ever happened to me. No way! Absolutely not! None the less, I somehow know how to fix it.

 

You'll need patience and a bit of force. Drop the boom until it's level, pull the sail out as far as you can without causing binding, cleat off the outhaul, and then use the furling line to wind the sail back onto the drum rather tightly. After that, pull out the sail a bit more if you can and repeat. The goal is to get the sail re-furled tightly with no folds. At some point, you may need to get on top of the cabin and pull the sail by hand to relieve a bind or two. The first step - putting the boom level - is important.

 

When this didn't happen to me, it was because I left the topping lift tight after sailing and then furled the sail with the boom angled up (aft end up by about 8"). This caused an uneven furl that wasn't an issue going in but was when unfurling. The parmanent fix is to always have the boom at the right angle when you furl and unfurl. It is surprising, but a few degrees of tilt can cause the sail to bind significantly, especially with a thick dacron sail that's a few years old.

I would also check the furling line to the drum. Last year the furling line was jumping a groove or two and that cause the line to bind on guides in the past.

I fixed the problem by replacing a worn furling line.

Bruce

Thanks to all for your replies, I did a bit of everything and it worked out just fine.

The followings were done while docked:

1. A lot of water on in-mast sail to lubricate (Thanks to Sam)

2. Tension the roll while working back and forth on the mainsail

3. Step on boom to use my fingers to keep the material inside the slot while a friend was pulling the main out

4. Main came out!

After an inspection, it seems that the furling line skips a groove, so I will replace it (Thanks to Bruce).

Also, I followed the instructions (I don't remember where I got this) to tighten the topping lift before furling... I'm not sure this a a good idea anymore.

Again, thank you all, this is appreciated.

RSS

Latest Activity

Brandon P is now a member of SeaKnots
Apr 18
Pankaj Tripathi is now a member of SeaKnots
Mar 19
Anna Kokou updated their profile
Mar 8
Profile IconDo My Assignment, William Noah, Thinq Proto and 4 more joined SeaKnots
Mar 7
Michael Boyle commented on CAN DRAC's group Beneteau 40 & 43
"Hi All, french built 2010 43 has been very dry down below but now a slow leak has occurred which is showing at the limber holes under the floor board in forward cabin. Bilge pump goes every 3hrs for 20secs. Not sure if it’s fresh/rain water or…"
Feb 28
LOLA commented on Franc's video
Thumbnail

Do you dream about offshore cruising?

"hello been years since on site. im having trouble changing my heading. are we limited to words? is there an instruction page? Thank you lola"
Jan 23
Filling Machine updated their profile
Dec 27, 2024
Packaging Machinery updated their profile
Dec 24, 2024
ADVERTISE ON SEAKNOTS CONTACT US AT: 
candrac@sailforwater.com

© 2025   Created by CAN DRAC.   Powered by

Badges  |  Report an Issue  |  Terms of Service