"Before you do that check all the steering hardware between the wheels and quadrant. There's a lot of hardware in the system that could induce friction causing a heavier feel to the wheel. I have a 2008 43 with well over 10K nautical miles on…"
Delivery of my Freedom 30
Comment
-
Comment by Ritchie Scott on January 30, 2009 at 7:35pm -
She moves well in the water. Congrat's on your purchase!
-
Comment by mike sproull on July 6, 2008 at 1:29am -
I also noticed you have no rigging shrouds and a free-standing mast,I looked into this and found out you have a carbon fiber mast and your boat should be a pleasure to handle.
-
Comment by mike sproull on July 6, 2008 at 1:13am
-
do you have a roller furling on the headsail?Hard to tell in your video although it doesn't look like it.Nice looking boat!
-
Comment by Jack Kamer on July 5, 2008 at 8:56pm -
Congratulations Lola!! She looks beautiful and from what I've heard, she will be a great sailor.
It's a little hard to tell from the video, what color is the canvas?
Latest Activity
Mike Brown replied to sail abroad's discussion Beneteau 40 2008 replacement rudder bearings in the group Beneteau 40 & 43
Simo Makkonen replied to sail abroad's discussion Beneteau 40 2008 replacement rudder bearings in the group Beneteau 40 & 43"I've been wondering, if I should do the same in my B40/2007. The rudder has become heavy (high fricton?) and the problem is not in the steering cylinder. Anyone had similar problem?
Simo"
Mike Brown replied to sail abroad's discussion Beneteau 40 2008 replacement rudder bearings in the group Beneteau 40 & 43"I'm a bit surprised you need to replace the bearings on an 2008. I've not heard of any issues other than early model 43s required a brace be installed at the quadrant. Actually the issue was discovered by Franc who happens to own and run…"
sail abroad added a discussion to the group Beneteau 40 & 43
Beneteau 40 2008 replacement rudder bearings
Has anyone replaced the rudder bearings on a beneteau 40 2008/9? If someone has done this job could they please tell me what the part numbers are for both the bronze upper and lower bearing sleeves and also for the nylon thrust washers. The jefa? rudder shaft diameter is 60mm.I have !ooked on the beneteau spare parts website without success.Also I am trying to find the workshop notes for rep!acing the bearings as I know with the oceanis 411 the bottom bearing is glued (3M 5200) in but I don't…See More
Mike Brown replied to Wayne's discussion New B 40 owner. in the group Beneteau 40 & 43"Wayne, welcome to the group. I think you'll find a wealth of information from all the members. And of course enjoy your B40, its a heck of a boat.
Mike
October Moon
2008 B43"
MAssimiliano replied to MAssimiliano's discussion foldng prop FOF on beneteau 40 in the group Beneteau 40 & 43"Hi Michael,
at the moment I prefer a Folding Prop due to better performance while sailing and also when "motoring".
My gearbox has a ratio in forwarding of 2.36.
don't worry... I'm not American....I'm Italian :-)
"
Michael Boyle replied to MAssimiliano's discussion foldng prop FOF on beneteau 40 in the group Beneteau 40 & 43"Hi,
I have a Kiwi feathering prop on my Beneteau 43, 4JH5E engine. It looks small and blades are a funny shape but it works perfectly. They set the pitch depending on size of engine, will need to know gearbox ratios, and it has full pitch in reverse…"
© 2016 Created by CAN DRAC.
Powered by
You need to be a member of SeaKnots to add comments!
Join SeaKnots