SeaKnots

Looks like this teak we varnished with Cetol is now badly damaged by the sun. :(

We want to strip all the varnish off and leave it bare for now. 

What would you recommend to remove the leftover varnish? 

We tried with a brush and this is as far as we got...

Looking forward to your thoughts!



Views: 47

Reply to This

Replies to This Discussion

This is what Cetol did to our wood when we still used the product 5 years ago.
If you want to leave the wood raw I'd hand-sand the varnish off to bare wood.
Heat gun with a plastic scraper will take it right off, just dont set the gun on high
i recently commented on another discussion about my assisting apply cetol on anothers boat...i would like to make mention(in case i was thought to have kudoed cetol) that my intention wasnt to rate cetol or recommend it, only mention th process that went into th product we used...that pic looks like what we hand-sanded, only to reapply.

RSS

Latest Activity

Mike Brown commented on CAN DRAC's group Beneteau 40 & 43
"Robert glad to hear you go the problem solved. mike"
Oct 11
Robert & Sandy commented on CAN DRAC's group Beneteau 40 & 43
"Thanks for all your comments my friends at Seaknots. The halyard has been rerun without passing through the small stainless steel eye, as seen easily in the pic provided by Chris on 17th August. All furling now takes place without any undue effort,…"
Oct 11
Mike Brown replied to Jochen Vetterlein's discussion O43: Good tracking on starboard side - poor on port side in the group Beneteau 40 & 43
"Well at least you’ve narrowed it down to the Genoa. I doubt here’s any issue with the hull or running gear. Nor do I think the slight list you have will have an impact either as many boats have the same based on how full the water and or…"
Oct 9
Jochen Vetterlein replied to Jochen Vetterlein's discussion O43: Good tracking on starboard side - poor on port side in the group Beneteau 40 & 43
"In the meanwhile, I performed some sailing tests trying to be as impartial as possible. I was sailing close hauled on the starboard and port side. I used the autopilot steering the boat at 37 degrees to the apparent wind. Apparent wind was 12 to 19…"
Oct 9
James Taylor replied to Jochen Vetterlein's discussion O43: Good tracking on starboard side - poor on port side in the group Beneteau 40 & 43
"Sounds like your rigging may be in need of tuning????? (Owned B43#19 for 10 years), Sailed from Mass to Tampa to Bahamas with it, great boat, no major issues at all. Boat has flat bottom basically so no need to put rails in water. I found it a very…"
Oct 9
Mike Brown replied to Jochen Vetterlein's discussion O43: Good tracking on starboard side - poor on port side in the group Beneteau 40 & 43
"I’d also do a test using only the main. The more testing you do the more likely you’ll find the problem. I’d also check to see how much the leeward shrouds sag during all the tests. Let us know what you find. Good luck Mike"
Sep 27
Jochen Vetterlein replied to Jochen Vetterlein's discussion O43: Good tracking on starboard side - poor on port side in the group Beneteau 40 & 43
"It is only when sailing close-hauled. Unfortunately, this is the only course, where performance really matters. I‘m going to perform two tests: - Sailing with genoa only (track cars on the same position). In this case any (unequal) trim…"
Sep 27
Mike Brown replied to Jochen Vetterlein's discussion O43: Good tracking on starboard side - poor on port side in the group Beneteau 40 & 43
"Our 43 had a shaft drive. Depending on how much water or fuel that was in her she would sometimes have a very small imbalance. Nothing that would cause her to sail unevenly. Do you have the problem on all points of sail? Is it more on any particular…"
Sep 27
ADVERTISE ON SEAKNOTS CONTACT US AT: 
candrac@sailforwater.com

© 2021   Created by CAN DRAC.   Powered by

Badges  |  Report an Issue  |  Terms of Service