SeaKnots

Marlene A. Sassaman's Blog – December 2010 Archive (2)

Living life, yea,

 While SPRAY rests quietly on the mooring in Vero...…

Continue

Added by Marlene A. Sassaman on December 29, 2010 at 12:00am — No Comments

I'm leaving on a Jet Plane..... NOT

Tomorrow I meet with my financial advisor. By the end of our meeting I will know what my boat buying budget will be for my solo circumnavigation. While my beer budget will realistically be close to $75,000 at the top end, my champagne taste will yield a Dragonfly 1200. Sometime between now and my 1 pm meeting tomorrow I promise to buy a Florida lotto ticket.

In the meantime, I seriously request suggestions for boats in the 30 foot range. A trimaran is my #1 choice. If I have to…

Continue

Added by Marlene A. Sassaman on December 12, 2010 at 8:26pm — 1 Comment

Latest Activity

sam replied to foster's discussion Spinakker halyard chafe in the group Beneteau 40 & 43
"I added a block on the mast above the ring. See attached picture."
10 hours ago
Jim Malone posted an event

SEAS Fall Picnic at Haverstraw Marina North Dock

September 28, 2014 from 11am to 5pm
SEAS FALL PICNIC. Sunday September 28th. 11AM to 5PMHaverstraw Marina North Dock 600 Beach Road West Havestraw NYhttp://www.meetup.com/SEAS-Bergen-County-Sailing-Meetup/See More
Tuesday
foster replied to foster's discussion Spinakker halyard chafe in the group Beneteau 40 & 43
"Hello Franc, Did you put this block directly on the  "O" ring that originally directed the spinnaker halyard. With the asymmetric spinnaker we have on a Facnor Spinex furling system we have to put a strong tension. Is there a risk…"
Monday
Franc replied to foster's discussion Spinakker halyard chafe in the group Beneteau 40 & 43
"I went up the mast and installed a block to put the halyard through. Problem solved! "
Sunday
foster replied to foster's discussion Spinakker halyard chafe in the group Beneteau 40 & 43
"Reply by foster 1 second ago Delete Hello Bruce, Thanks for the answer. I think I am going to modify this Beneteau Z spar set up to improve and diminish chafe and then put a new halyard. Simplest would be to attach a block to the ring. But this…"
Friday
foster replied to foster's discussion Spinakker halyard chafe in the group Beneteau 40 & 43
"Hello Bruce, Thanks for the answer. I think I am going to modify this Beneteau Z spar set up to improve and diminish chafe and then put a new halyard. Simplest would be to attach a block to the ring. But this could interfere with the genoa…"
Friday
Bruce Bogdanoff replied to Ed English's discussion Tac Failure on Ben 40
"Check you wiring harness on the back of the engine panel. Pull the connectors apart and together several times to remove corrosion. The spray with WD 40 or electronics cleaner. I the put an electrical Dielectric grease  on the connectors before…"
Friday
Bruce Bogdanoff replied to foster's discussion Spinakker halyard chafe in the group Beneteau 40 & 43
"I have a pole lift that goes to the pulley (Reel?) below the bracket that captures the Gennaker Halyard. I also have chafe on the line and on my second spinnaker line. The first one was replaced under warrenty as the chafe occurred within a year of…"
Friday
ADVERTISE ON SEAKNOTS CONTACT US AT: SeaKnots@SeaKnots.com

© 2014   Created by CAN DRAC.

Badges  |  Report an Issue  |  Terms of Service