SeaKnots

A moment ago I was reading on another forum about a blower motor not working on a Beneteau 361 and then it occurred to me that I've never seen the engine compartment blower on my B40. If anyone here knows would you please enlighten me on it's location?

Thanks,

Wayne

Views: 115

Replies to This Discussion

The engine compartment exhaust blower is located on the port side behind the vent. You have to remove the propane locker to access it. To remove the propane locker you have to crawl into the rope locker below it and remove the hose that’s installed to exhaust any leaking propane. Don’t forget to reinstall it. The fuse for the fan is 10 amp and is located in the right hand side of the battery compartment. They also use the fuse for power to battery isolators. 
I hope this helps. 
Mike

Thanks for the info Mike. Now I need to verify it works. I know it gets extremely hot in the engine compartment after a while. 

Wayne, my never ran. I discovered the issue when the fuse blew. I then foolishly bought a new fan and installed it only to have it sound like a helicopter in the cockpit. I cushioned it and tightened it to no avail. I finally disconnected it without any issues. 
Mike

RSS

Latest Activity

Kerim N replied to Randy Brown's discussion Beneteau 40 Black Mesh Window Covers in the group Beneteau 40 & 43
"Hello Randy, New to the group, going through the posts, I have come upon this thread.  I was considering tinting my windows of my Beneteau 43 with a darker tint, but I really like your idea.  So I will copy with…"
Jan 6
Kerim N joined CAN DRAC's group
Thumbnail

Beneteau 40 & 43

A place to exchange thoughts, ideas and discussions about the Beneteau/Oceanis 40 and 43 models.
Jan 6
Kerim N is now a member of SeaKnots
Jan 5
Mike Brown replied to Larry Witty's discussion B43 Windlass Drainage in the group Beneteau 40 & 43
"Larry good luck. And remember to use the KISS Method when troubleshooting. Keep It Simple Stupid haha. It’s an old and basic concept that dictates you always do the easiest and obvious stuff first. Then if it doesn’t fix it get more…"
Dec 23, 2021
Larry Witty replied to Larry Witty's discussion B43 Windlass Drainage in the group Beneteau 40 & 43
"Thanks Mike, good advice which I will follow."
Dec 23, 2021
Mike Brown replied to Larry Witty's discussion B43 Windlass Drainage in the group Beneteau 40 & 43
"Sounds like you need to give that windlass some TLC. I used to clean and apply a light coating of grease to all the surfaces in and under the gypsy. It remained smooth over a 10 year period. Five of those years were spent cruising full time on the…"
Dec 23, 2021
Larry Witty added a discussion to the group Beneteau 40 & 43
Thumbnail

B43 Windlass Drainage

Doing some maintenance on my B43 Quick Antares windlass this year. After removing the windlass, I knew instantly that I should have been doing this at least ever other year.  The windlass was preforming weak and slow with a noise which made me think the motor brushes or a bearing was going out, thus the reason for removing it.What I found upon removal was a tremendous amount of salt and sand on the top part of the gearbox, literally packed in. Upon cleaning everything up, luckily all bearings…See More
Dec 23, 2021
James Taylor replied to Robert & Sandy's discussion DOLPHN 40 AMP BATTERY CHARGER in the group Beneteau 40 & 43
"Happy Holidays to you and yours. Happy to hear its working properly."
Dec 17, 2021
ADVERTISE ON SEAKNOTS CONTACT US AT: 
candrac@sailforwater.com

© 2022   Created by CAN DRAC.   Powered by

Badges  |  Report an Issue  |  Terms of Service